How to disassemble the LED downlight of Bihua lighting
Led downlight is a product developed on the basis of LED downlight brand. Low carbon, long life, good color rendering and fast echo speed are its advantages. However, this kind of lamp is gradually used. Hallway, living room, conference room and other places are very common. The ceiling with suspended ceiling is more appropriate. How to remove the LED downlight?
It's very simple. Downlight is a kind of lighting fixture embedded in the ceiling. There is a spring clasp at both ends, which can be taken down directly. Downlights generally have a screw cap, which can be directly installed with incandescent lamps or energy-saving lamps. Led downlight has been used for a long time, showing problems. How to replace and repair it at this time?
1. Prepare tools needed for LED downlight replacement and repair. Generally, common tools for replacing and repairing led downlights are: electric tape, a set of LED downlights of the same model, pliers, and a small hand saw if necessary.
2. Turn off the power and slowly turn off the light
If you don't pay attention to the spring clip, you will be hurt by the spring clip if you pull the lamp head down, so you should be careful to remove the old bad led downlight.
3. Then take apart the connector and replace the lamp holder. If the driver does not move, turn on the light switch. If the light is not on, it can be determined that the driver is faulty, and replace the driver.
4. Turn off the light switch at the moment to turn off the main power supply, and then turn off the power input line of the driver (it can also be cut short directly), then remove the broken driver, and then peel the new power input section of the driver, and peel the two light wire ends.
5. Wrap one of the driver power lines around one of the lamp power lines (the lighting power is not positive or negative), and stick it with electric tape. The other one is connected with the same method and wrapped with electric tape.
6. It will be finished. Next, power on the experiment, turn on the switch and the light will be on. If it is not on, repeat the above steps but directly replace the LED downlight instead of replacing the driver.
Source: Bihua lighting http://www.zsbihualed.com
-
09-15
What is the difference between LED downlight and LED spotlight
What's the difference between LED downlights and led spotlights? In home decoration, led downlights and led spotlights are used more. On the one hand, they are needed for auxiliary lighting lamps such as LED downlights and led spotlights. On the other hand, led downlights and led spotlights are not limited by decoration styles. Basically, each decoration style is suitable for LED downlights and led spotlights. All kinds of styles can be taken into consideration. Not only that, led downlights and
-
09-15
The difference between LED ceiling lamp and LED panel lamp
Led ceiling lamp is generally installed in the interior of the room. The appearance design of the lamp is that the upper part is flat, and it is installed close to the roof, like adsorbing on the roof, so it is called led ceiling lamp. The LED panel lights are more diversified, including horizontal LED panel lights, embedded LED panel lights, ceiling LED panel lights, hanging LED panel lights, circular LED panel downlights, and circular ceiling LED panel downlights. As the ceiling mounted panel
-
09-15
Three purchase directions of LED wall lamp
In fact, the wall lamp is a kind of lamp which plays an important role in home decoration. Wall lamp can make your home glow with unique brilliance. At present, led wall lamp is used at most. The light of LED wall lamp is elegant and harmonious. It can decorate the whole environment with elegance and high profile. It can make home play the role of finishing point and add different aesthetic experience. This shows that led wall lamp is also very necessary to install, so the premise of installatio
-
09-15
How to solve the problem of heat dissipation for LED panel lamp?
In the LED panel lamp, there are three basic stages of heat transfer, from integrated chip to epitaxy, from packaging base steel plate to heat sink or shell. At present, the technical problem of LED heat dissipation is that led nodes are limited by temperature. High temperature will cause led integrated chip, luminous powder, packaging epoxy resin service life is reduced. In order to keep the advantages of high efficiency and long life of LED, the junction temperature of LED must be controlled.